Hello, I am hoping someone can help me. My starboard trim works well and I can hear the mechanism working and see the movement on the gauge. My port trim seems to be stuck in the max UP position. The gauge shows the highest setting and when I press the down button I can hear the trim mechanism working but it doesn't stop humming as long as the button is pressed down (on the starboard engine once the trim hits the lowest or highest setting on the gauge, it stops humming even if I am still pressing the button. What do you think is causing this? What are the effects of sailing the boat with mismatched trim levels on the engines? Also, what does the middle button on the trim controls do?

I have a well kept 1986 Riviera (2807). I recently pulled up to a dock and shut down. I turned on the blower and it ran for a few minutes then suddenly stopped. Started checking outlets and interior lights, some worked some did not. Plugged into shore power and still no go... Pulled the dash cover and it seems that there is no current going to the "blower" toggle switch. Don't see any fuses? Any ideas? Much appreciated!

I have an '86 Carver Mariner 3297. My water line from the dock water connection broke. The line extends into the engine compartment, but I can't see where it broke from. It appears to me that, perhaps, the line was branched off of the cold water supply to the water heater as I can only find one water line (gray Pex) running from the pump to the rear of the boat. Looking for insights into where that line was connected, water line schematic, etc.

Just reduced...$239,900 CAD or $178,000 USD
Winedown is a modern vessel in excellent condition & well maintained with many upgrades..The design includes near 7 ft salon headroom...More space than any other 40 FT boat made..Only produced from 2000 to 2006..Volvo TAM 6 diesels with 2300 hours & Kohler 10 KW generator..(hours approximately 800)..Factory installed bow thruster & aftermarket side shift stern thruster (motor 2 yrs old)..Turbos reconditioned 3 yrs ago with new bearings & seals & new waste gates..Bridge enclosure has polycarbonate front windows & balance of vinyl is strata glass all in eccellent condition..Helm has Raymarine 12 " Axiom GPS with Avionics software charting..Also includes Raymarine VHF, autopilot, radar capable, excellent aftermarket stereo system with multiple speakers & remote control in aft deck..Eight batteries on board all new at start of 2022 season except generator batter is 3 yrs old..Bow pads for relaxing after dining & watching sunsets while anchored out..Aftermarket dinghy lift so no need to tow inflatable..Anchor wash, stainless steel 40 pound anchor & 125 feet of chain & windlass pedals on bow which can also be operated from helm..Swim platform wash down hot & cold water..Salon has two reclining chairs on starboard side & sofa with pull out storage on port side..Gall has microwave & electric cooktop..Three air conditioners /heat for zone comfort..Main salon, berth & master stateroom..Two staterooms & two heads each with showers..Salon has 40" flat screen TV & master has another flat screen TV..LED lighting throughout..Ample storage throughout vessel in salon, staterooms & heads..Liveaboard capable vessel will provide many years of enjoyable cruising..Call RIck at 416-566-0106 or email rckmoore@rogers.com..

Hello everyone, bought a basket case Carver 380 and I’m looking to see if anyone out there has a carver 380 in a diesel has I’d like to keep this boat for the next 20 years it currently has MerCruiser 7.4 MPI magnum 380 hp engines which I’m not fond of, I would like to re-power this boat with diesels, and would like to get as much information as I can in regards to engines, transmissions running gear, fuel tanks, etc. if there’s anyone that has a Carver 380 diesel or information as to what I would need to make this happen I would be greatly appreciated. Thanks in advance, Jeff.

Hey all! I have a 1995 Carver 320 Voyager. I am looking for a used or rebuilt Walter RV26 V-Drive with a 2.05-1 gear ratio. I can't seem to find one here locally (I'm in Louisville, KY). Can anyone help?

With respect to volvo tam 63 diesel engines, are there hour meters somewhere on the engines...Digital display on tachometer for starboard side is not working...

I am going to upgrade the temp gauges on my 1994 7.4 closed cooled Bluewater 7.4. I saw two sanders coming out of the tstat housing. WHich is teh sender for gauge? The one facing FWD or the one facing AFT?

Thanks!

Hi all my sliding glass door saloon door is getting harder to slide open ... im thinking it may need new rollers .. so has anyone attempted to remove the glass sliding door, does it have a roller type system, is there a procedure to removing it.. any pictures would be great ..cheers

Anyone has the manual for this A/C model SCL5016.