Have a 1986 Carver Santa Fe and can not figure out where the front bilge pump goes to ran a 20 foot snake through it and could not find out where it goes. No hoses run out through the hull fitting called carver and they do not know either think it runs water from front bilge to engine compartment bilge. Oh well

I'm looking at a 1995 Carver 250 Mid Cabin with a Volvo Penta 7.4 in it . Anyone know the H.P. for that motor and that year? Thanks

I am just purchasing a 2004 466. while we were on board for the survey and sea trial yesterday, while we were on shore power, I could only get all of the 110 powered devices to operate while the inverter interface was in the on position. Is this normal? In our motorhome, I turn off the inverter when we are hooked to shore power, but the carver only seems to work all of the 110 when the inverter is on, even while on shore power? Does anyone know if this is correct? shore power was working and breakers were on, and was showing 110 on the gauge.

thank you for the feedback

I just took possession of my new carver this past week. It's a 1997 370 Voyager in great shape. In fact, just had the bottom painted yesterday and waiting for the wind to die down to get it back to the slip. Have to find a new slip as well, current one is just too thin and rubbing up the sides a little.

Looked for quite some time and opted for this one as I loved the space, large fridge, shower area and one of the few boats I can stand up in at 6'4". A little low when you first walk in but that's ok .

Had a 36' Hunter a while back and loved sailing but figured I can use this one for an extension of our Condo since it's not terribly large. Not just that but old motorcycle injuries make the shoulder a little sore from winching.

She only has about 800 hours on her, already ordered some new canvas, new front cushions and a few little things but the carpet has some stains so being a bit of a carpenter myself, likely going to pull out the carpet and do something else. Not sure if I'll go for that braided vinyl, hardwood or….?

I'm not one to wait to make decisions so I'll likely start tearing out the carpet next week unless I can fight the urge . Ordered new curtains and tore out the mini blinds, thinking I'll get some of the cloth mini blinds I've seen at Lowes but I'll search for forum first for some solutions.

Anyway, been dabbling around on the net and this forum seems fun so I'll make sure to poke around. I'm new to the area here so if anyone is looking to say hello and lives around Marina Del Rey, would be great to make some new friends. I'm pretty handy and always willing to help anyone in need so drop me a note if I can lend a hand!

Nice meeting everyone!!

I have a 1996 Voyager320 and need to replace the stipe on the waterline. I have the original part number, and am looking for the original Carver stripe perhaps?

hello all
Just recived my 1995 33' maniner about 3 weeks ago. Survey and sea trials went well and I am now in dry dock and cant wait for spring. I noted that my props seem tight. Takes 2 hands to turn them. Survey stated they were free when the boat came out of the water. Is this normal ? Also will be happy take any input on this boat like fuel millage standard speed/ rpms.
any info will help as I am new to a boat this size. My last boat was a 24' bayliner (2452)

thanks
chris & lois
rivercamper

[b][/b]These 4 blade beauties are tuned and polished. Came off of a 3207 with twin 270 Crusaders. Gotta love the CDN dollar if you are south of the boarder!!! $500 CDN or $365 US each

I have a real strange issue. I have a 7.4 liter Volvo penta engines. The engine ran for 58 days as we traveled south and every thing was great. IT sat 2 wekks. Engines Flushed with fresh water when we stopped. It ran great for 5 to 7 minutes and then increased RPM to 2600 and would not go down. Switched AIC valve. no Help. We swithched the computer and this was not the issue. Ohmed and continuity to wires to value no issue. Checked wires to ground no issue. What can it be. We need help!!!!

We have a 466 Carver MotorYacht. I was wondering if anyone has replaced the blinds on their boat. If so, what company did you use?

Our 2003 530 with 75 series engines (560 hrs) has very low (1 PSI) indication on the EVC digital displays yet the analogue gauges in the panel show perfect indications (well above half scale) Both engines the same- no alarm indications at all. Thoughts? Thank you!