Hi Fellas,
Our 36 Carver has twin Volvo Penta 740B gas engines. My port tach has stopped working over the winter, I checked the connections and everything looks good. Would anyone know if the tachs are driven from the alternator or the distributer?
Thanks for any help

I hope this message finds you well. I recently acquired a 1989 34' Santego, and I’m in a bit of a bind. Unfortunately, the drain plug wasn’t removed over the winter, and I’m having difficulty locating it. I would greatly appreciate it if anyone could share a picture or diagram indicating its location. I’ve managed to remove a significant amount of water using a trash pump, but there’s still a concerning amount left in the bilge and below in the engine area.

Hello brothers
Going down to the boat Saturday and going to be hot I was wondering if I can take the filter out, clean it and put it right back in or does it need to dry? Guessing it would probably need to dry
Thanks
Geo

New to the Carver yacht owners forum.
Wondering if anyone knows were to get replacment keys for the entrance to the main salon on a C52 Command bridge. I havent had any luck with locks smiths being able to make an extra key. The key is a TrioVing (ass abloy) numbers on the reverse side are 15-89871. Looking for any assistance. thanking you in advance.

Hello all, i have a 1993 carver 350 aft cabin the previous owner somehow bent the shaft it also had a little damage to the prop. This winter i removed the shaft and props and had them all refinished (New Shaft) .... reinstalled everything dropped the boat in the water .. and again anything over 1200 rpm it wobbles again... a bit frustrating as you can imagine... Any idea what could be causing this ? could it be the struts holding the shaft? if so where can i get some of those ... Thanks in advance...

Hi - I'm brand new to the forum and hope I'm in the right place for my question. I have a 2002 Carver 350 Mariner and recently the lock to the cabin door (sliding glass door) gave up the ghost. The key turns easily, but the lock mechanism is no longer moving/closing. Has anyone else ever had this issue and, if so, who could I call that could possibly repair it? I tried a locksmith and he said since the lock body is inside the channel of the sliding door, he wouldn't be able to repair it. Should I call a sliding glass door company or does anyone have other suggestions? Thanks in advance!

Hello everyone, just made it to Mobile AL this week in my Carver from Chattanooga TN. Great trip!

Looking for info on a relay to use (in front / Galley bilge) to close / open the 120V 10Amp circuit that feeds my AC water cooling pump. A 12V powered relay, allowing a 120 V 10-amp circuit to be started and stopped by the relay.

Why am I doing this?
1) I leave my AC on in the boat - It is Hot down here.
2) I am in brackish / salt water now so corrosion could create a leak in that system
3) My Victron Cerbo GX has a relay switch that can throw on alarm open/close.
4) I also monitor for high water in the bilge that alarms

The thought is if the high water alarm goes into alarm mode, The Cerbo deenergizes the N/O relay thus disconnecting the AC 120V power to the AC pump. If the pump is filling the boat, this will stop that from continually filling the boat with water. If it is leaking in the boat. Both AC's will go off but, at least the water will not continually fill the boat.

Side note: many of my videos from the trip are up on YouTube
https://www.youtube.com/playlist?list=PLPGP5FV0qDeZH4FzKr-c3PmpRvBtWht_0

I need to replace the water inlet, but unfortunately the replacement is slightly larger than the previous one. Jabsco for some reason decided to replace the old style which needed about a 3 1/8" hole with one that's about 3 1/2". I have a couple of questions I'm hoping I can get some feedback on:

- I was thinking about using this method to drill a larger hole: https://youtu.be/vOUfFaIJUqo?si=wP9k6RR7aC-3mwpc. The transom where the inlet is has fiberglass which is about 1/2" thick. Will this method be okay to enlarge the hole?

- Will I need a diamond or carbide tipped drill bit, or will a bi-metal one work okay on the fiberglass? https://www.homedepot.com/p/Milwaukee-3-1-2-in-Hole-Dozer-Hole-Saw-49-56-9641/202327759

- Regarding the plumbing part of this, is it okay to attach the inlet to any cold-water pipe? It appears the inlet pipe had broken off and was capped off somewhere, so I'm not 100% sure where it originally was fed into the system. I'm thinking it was attached to near where the cold water faucet is on the aft shower.

Thanks for any input! Boat is a 1995 440 aft cabin.

Hello everyone, just wondering if anyone used the product Airlock ionizer to keep their boats smelling fresh and clean? Keep seeing their ads and read the reviews. Seems very impressive, hoping to get firsthand knowledge.
Thanks
Have fun and be safe
Geo

Hi
My 2001 Mariner 350 needs some internal repairs on the sofa. Trying to find the a source for the vinyl material ie a colour match for the original Carver colour swatches.

I'm in Ontario Canada so any local sources appreciated if you know some...

Thanks!