Welcome to Carver Yachts Owners Forum
We are a boating forum for owners of Carver Yachts to enthusiastically discuss all aspects of Carver Boat ownership. Whether you are looking for your first Carver or currently own one, you are sure to feel at home on CarverYachtOwners.com
You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
Replacement of VHF antenna on 2000 396 aft cabin
-
tgebler
Topic author
- First Mate
- Posts: 173
- Joined: June 10th, 2018, 1:58 pm
- Vessel Info: 2000 396 AC
- Location: Pittsburgh
- Has thanked: 5 times
- Been thanked: 23 times
Replacement of VHF antenna on 2000 396 aft cabin
Anyone replaced the antenna and cable? I would appreciate any recommendations, short cuts, etc. Thanks.
-
Cooler
- Admiral
- Posts: 1665
- Joined: May 22nd, 2018, 12:09 pm
- Vessel Info: 1995 Carver 330 Mariner
Twin 350XL Crusaders
Home port: Menominee, MI - Location: Green Bay, WI
- Has thanked: 68 times
- Been thanked: 400 times
Re: Replacement of VHF antenna on 2000 396 aft cabin
Very common job. Just google VHF antenna replacement youtubes. You will get several. 
er
erCooler By The Lake
( All weather people have to say this on air, near lakes )
( All weather people have to say this on air, near lakes )
-
Viper
- CYO Supporter
- Posts: 6067
- Joined: July 10th, 2015, 9:58 pm
- Vessel Info: 1989 Carver 3807 Aft Cabin
- Location: Ontario, Canada
- Has thanked: 460 times
- Been thanked: 1710 times
Re: Replacement of VHF antenna on 2000 396 aft cabin
Are you seeking advise on how to do it or how/where to run the cable on a 396?
-
tgebler
Topic author
- First Mate
- Posts: 173
- Joined: June 10th, 2018, 1:58 pm
- Vessel Info: 2000 396 AC
- Location: Pittsburgh
- Has thanked: 5 times
- Been thanked: 23 times
Re: Replacement of VHF antenna on 2000 396 aft cabin
How to run cable is my issue
-
Viper
- CYO Supporter
- Posts: 6067
- Joined: July 10th, 2015, 9:58 pm
- Vessel Info: 1989 Carver 3807 Aft Cabin
- Location: Ontario, Canada
- Has thanked: 460 times
- Been thanked: 1710 times
Re: Replacement of VHF antenna on 2000 396 aft cabin
Hopefully someone with the same model/year will chime in with how they access the routing.
-
Tireless
- Commander
- Posts: 460
- Joined: October 16th, 2018, 4:51 pm
- Vessel Info: 2006 Carver 44 CMY
Volvo Penta D6 370 HP - Location: Port Severn, Ontario
- Has thanked: 183 times
- Been thanked: 187 times
Re: Replacement of VHF antenna on 2000 396 aft cabin
I have a Carver 44 CMY and it should be the same run. It would not matter if the antenna is mounted on the port/starboard arch. Remove the panel on you helm to expose everything under the dash.
For a starboard arch mount, run your new cable from the radio o the starboard side and down the starboard side of the brow, under your co pilot seat, behind the ice maker and cupboard and to the arch. There should be an access panel on the inside of the arch and then to where your antenna is mounted. This is the side mine is on.
On a port install, run the cable to the port side of the dash and then under the bench seat. Remove the bench seat cushion to allow you access. Run the cable back to the port side arch. There should be an access panel on the arch to assist in running the cable up to the mounting position.
To assist you to get the cable through, use an electrical fish tape. When I run wire through my boat I normally pull some twine/heavy string/nylon strap through first and then use that for the cable, but you don't have to. To set you up for the next thing you need to do in the future, I would also pull a twine/string/nylon strap through with your cable and leave it there for the next time you need to fish a wire through that area.
Hope this helps you.
Greg
For a starboard arch mount, run your new cable from the radio o the starboard side and down the starboard side of the brow, under your co pilot seat, behind the ice maker and cupboard and to the arch. There should be an access panel on the inside of the arch and then to where your antenna is mounted. This is the side mine is on.
On a port install, run the cable to the port side of the dash and then under the bench seat. Remove the bench seat cushion to allow you access. Run the cable back to the port side arch. There should be an access panel on the arch to assist in running the cable up to the mounting position.
To assist you to get the cable through, use an electrical fish tape. When I run wire through my boat I normally pull some twine/heavy string/nylon strap through first and then use that for the cable, but you don't have to. To set you up for the next thing you need to do in the future, I would also pull a twine/string/nylon strap through with your cable and leave it there for the next time you need to fish a wire through that area.
Hope this helps you.
Greg
Return to “Electronics & Navigation”
Who is online
Users browsing this forum: No registered users and 6 guests
Sponsors