Welcome to Carver Yachts Owners Forum
We are a boating forum for owners of Carver Yachts to enthusiastically discuss all aspects of Carver Boat ownership. Whether you are looking for your first Carver or currently own one, you are sure to feel at home on CarverYachtOwners.com
You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
2006 mariner 36
- Maikgruft
- Scurvy Dog
- Posts: 1
- Joined: June 23rd, 2022, 3:49 pm
- Vessel Info: Marina36 2006 volvo penta engines
- Location: Michigan
- Been thanked: 1 time
2006 mariner 36
The boat has the 5.7 volvo penta engines .
The survey found no issues with the boat .
The engines both have 300 hours on them .
As it was stored in a heated place 2 hours away from location , I brought over the water to my home .
My problem is that both engines only make 3200 rpm and then stull out .
When I reading correctly the engines should make 5500 rpm .
As I ask a mechanic ,he said it could be the wrong probs .
But it still shut off on me , even in neutral at 3200 .
If it would be the gas pumps, then either off the engines would shut off at diffrent idel.
Any one out here no what my problem is ,or if it is from carver restricted in the beginning.
Thanks for any input
- bud37
- Admiral
- Posts: 4689
- Joined: April 23rd, 2015, 10:22 pm
- Has thanked: 550 times
- Been thanked: 1150 times
Re: 2006 mariner 36
Your engines are electronic/computer controlled and with the boat being new to you, maybe not a bad course of action.....good luck with your new boat.
- pepmyster
- Admiral
- Posts: 978
- Joined: June 5th, 2018, 7:17 am
- Vessel Info: 2004 Carver 360 Sport Sedan
8.1 Volvo Penta
Fresh water boating - Location: Ottawa
- Has thanked: 445 times
- Been thanked: 194 times
Re: 2006 mariner 36
- bud37
- Admiral
- Posts: 4689
- Joined: April 23rd, 2015, 10:22 pm
- Has thanked: 550 times
- Been thanked: 1150 times
Re: 2006 mariner 36
- km1125
- Admiral
- Posts: 3355
- Joined: February 28th, 2017, 6:04 pm
- Has thanked: 59 times
- Been thanked: 976 times
Re: 2006 mariner 36
When were the fuel filters replaced... and do you know if ALL the fuel filters were replaced? Some boats/engines have multiple sets of filters in line, so any one being clogged up will limit engine performance.
-
- CYO Supporter
- Posts: 2292
- Joined: March 28th, 2016, 10:52 pm
- Vessel Info: 1998 Carver 355
Suspicious Fishes !
2022 Kawasaki 310X - Location: upper chesapeake bay
- Has thanked: 314 times
- Been thanked: 585 times
Re: 2006 mariner 36
When running in gear, those engines should make at least 4500 rpm. I wouldn't push them to 5500 for more than a minute, just to see if they can get there.
-
- CYO Supporter
- Posts: 5819
- Joined: July 10th, 2015, 9:58 pm
- Vessel Info: 1989 Carver 3807 Aft Cabin
- Location: Ontario, Canada
- Has thanked: 432 times
- Been thanked: 1595 times
Re: 2006 mariner 36
- buster53
- Admiral
- Posts: 996
- Joined: May 12th, 2017, 10:41 am
- Vessel Info: 2001, Carver 356
- Location: Lower Potomac, VA
- Has thanked: 8 times
- Been thanked: 254 times
Re: 2006 mariner 36
- JohnS
- Deck Hand
- Posts: 53
- Joined: October 25th, 2020, 7:58 am
- Vessel Info: 2003 350 Mariner
- Location: DFW
- Has thanked: 38 times
- Been thanked: 16 times
Re: 2006 mariner 36
- JohnS
- Deck Hand
- Posts: 53
- Joined: October 25th, 2020, 7:58 am
- Vessel Info: 2003 350 Mariner
- Location: DFW
- Has thanked: 38 times
- Been thanked: 16 times
Re: 2006 mariner 36
New rotors, caps and plug wires same issue so after a lot of research i replaced the fuel injectors with a set of rebuilt ones, 4200 rpm and she runs like new. I'm sending the old injectors out to have them cleaned and will be changing out the port injectors.
https://highperformanceinjectors.com/pa ... g-services
Return to “Gas Engines/Transmissions”
Who is online
Users browsing this forum: No registered users and 13 guests