Welcome to Carver Yachts Owners Forum

We are a boating forum for owners of Carver Yachts to enthusiastically discuss all aspects of Carver Boat ownership. Whether you are looking for your first Carver or currently own one, you are sure to feel at home on CarverYachtOwners.com

You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

Swim platform

User avatar

Topic author
Ghyden
Scurvy Dog
Scurvy Dog
Posts: 4
Joined: September 23rd, 2013, 11:41 pm
Vessel Info: 2003 366 Motor yatch. Twin 6.2 320 hp each
Location: Grand Lake, OK

Swim platform

Postby Ghyden » September 25th, 2013, 1:29 am

I recently purchased a 2003 366. I am wanting to have an extended swim platform installed. Boat is on a freshwater lake in the Midwest. I also want to install underwater lighting. Can anybody steer me in the right direction on the platform. So far I have been searching the Internet. I don't know if these are premade or if I will have to have one custome made. Any ideas???

User avatar

SHEMP
Deck Hand
Deck Hand
Posts: 51
Joined: March 7th, 2013, 7:43 pm
Vessel Info: 2000 CARVER 456 MY
Full Bridge and aft deck enclosure
Originally purchased in Staten Island
Second owner also purchased in Staten Island in 2012
Now berthed in Toronto Canada
A wonderful and fully appointed luxury yacht.
Location: Toronto Ontario Canada
Has thanked: 7 times
Been thanked: 4 times

Re: Swim platform

Postby SHEMP » October 6th, 2013, 11:31 pm

Were these extended platforms available from Carver as original equipment? Perhaps they might have the molds . I highly doubt you will find a swim platform that will fit your boat. Carver would have only built as many as were ordered. If they have the molds its not likely they will let you use them. I think your best bet is to find a good Fiberglass fabricator in your area and have one built .
I'm guessing between $3000 to $5000. Measuring boat and platform , making plug, making mold, pulling part, finishing the part and installation. Keep in mind the platform is through bolted to the hull sides and transom.
You might be able to offset the cost by renting out your mold.
Good luck
Shemp
User avatar

United States of America
Ramsport47
Commander
Commander
Posts: 376
Joined: February 10th, 2013, 7:13 am
Vessel Info: 1998 Carver 310 Santego
Has thanked: 72 times
Been thanked: 56 times

Re: Swim platform

Postby Ramsport47 » October 7th, 2013, 12:36 pm

Try www.swimplatforms.com or www.myswimplatform.com We've used them both. They will both custom make a platform for your boat, although swimplatforms.com do have a size limitation where the other one does not seem to.
Kenny
1998 Carver 310 Santego
T-Merc 350 Mag MPI (300hp)
Port: Cedar Point Marina, Sandusky, Ohio
User avatar

Topic author
Ghyden
Scurvy Dog
Scurvy Dog
Posts: 4
Joined: September 23rd, 2013, 11:41 pm
Vessel Info: 2003 366 Motor yatch. Twin 6.2 320 hp each
Location: Grand Lake, OK

Re: Swim platform

Postby Ghyden » October 23rd, 2013, 12:34 am

Thanks for the feedback.

Return to “The Project Center”



Who is online

Users browsing this forum: No registered users and 54 guests