Welcome to Carver Yachts Owners Forum

We are a boating forum for owners of Carver Yachts to enthusiastically discuss all aspects of Carver Boat ownership. Whether you are looking for your first Carver or currently own one, you are sure to feel at home on CarverYachtOwners.com

You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!

1750 RPMS

Anything related to the operation of your boat. Steering, Bilge Pumps, thru-hulls, bottom paint, etc.
Post Reply
User avatar

Topic author Canada
Michaemac
Scurvy Dog
Scurvy Dog
Posts: 3
Joined: April 25th, 2021, 6:48 pm
Vessel Info: 2005 Carver 56 Pilothouse
Location: Canada

1750 RPMS

Postby Michaemac » April 25th, 2021, 6:58 pm

Anyone have a solution as to why my boat won’t rev higher than 1750 rpms? I have 2005 56 Pilot house.
You do not have the required permissions to view the files attached to this post.
Top

User avatar

United States of America
km1125
Admiral
Admiral
Posts: 3525
Joined: February 28th, 2017, 6:04 pm
Has thanked: 72 times
Been thanked: 1056 times

Re: 1750 RPMS

Postby km1125 » April 25th, 2021, 7:20 pm

I don't know that system at all, but it seems like Error 55 on a CruiseCommand comes back to a battery issue.

Is this just one engine or both?
Top
User avatar

Topic author Canada
Michaemac
Scurvy Dog
Scurvy Dog
Posts: 3
Joined: April 25th, 2021, 6:48 pm
Vessel Info: 2005 Carver 56 Pilothouse
Location: Canada

Re: 1750 RPMS

Postby Michaemac » April 25th, 2021, 7:42 pm

It’s on both engines. Not sure if that’s the issue. I will power them off and back on and see if that’s the issue. When I run her at 1750 it shows 100% load on the engines?
Top

Canada
Viper
CYO Supporter
CYO Supporter
Posts: 6067
Joined: July 10th, 2015, 9:58 pm
Vessel Info: 1989 Carver 3807 Aft Cabin
Location: Ontario, Canada
Has thanked: 460 times
Been thanked: 1710 times

Re: 1750 RPMS

Postby Viper » April 25th, 2021, 8:32 pm

Did you check the basics first; clean air filters, clean fuel filter assemblies, new fuel filters? Do they smoke a lot? Does the boat get used a lot, how old is the fuel?

It would help to know what engine package we're talking about here.
Top
User avatar

United States of America
buster53
Admiral
Admiral
Posts: 1041
Joined: May 12th, 2017, 10:41 am
Vessel Info: 2001, Carver 356
Location: Lower Potomac, VA
Has thanked: 9 times
Been thanked: 262 times

Re: 1750 RPMS

Postby buster53 » April 25th, 2021, 10:17 pm

When was the last time the bottom and running gear was cleaned?
Top
User avatar

Topic author Canada
Michaemac
Scurvy Dog
Scurvy Dog
Posts: 3
Joined: April 25th, 2021, 6:48 pm
Vessel Info: 2005 Carver 56 Pilothouse
Location: Canada

Re: 1750 RPMS

Postby Michaemac » April 25th, 2021, 10:44 pm

All the maintenance has been done on the. Cummings engines. J believe they’re 660’s. It just happened for the first time last week.
I’m thinking of restring the cruise commander. I also have trolling valves installed in vancouver for fishing. I got some wired going on.
Top
User avatar

United States of America
km1125
Admiral
Admiral
Posts: 3525
Joined: February 28th, 2017, 6:04 pm
Has thanked: 72 times
Been thanked: 1056 times

Re: 1750 RPMS

Postby km1125 » April 25th, 2021, 11:26 pm

Is it possible it's in trolling mode? Again, don't know that system but just doing some quick reading it seems like you can toggle it into a "trolling mode" which restricts the engines so they only will go to part throttle.
Top

Canada
Viper
CYO Supporter
CYO Supporter
Posts: 6067
Joined: July 10th, 2015, 9:58 pm
Vessel Info: 1989 Carver 3807 Aft Cabin
Location: Ontario, Canada
Has thanked: 460 times
Been thanked: 1710 times

Re: 1750 RPMS

Postby Viper » April 26th, 2021, 10:15 am

Some applications also have a switchable low rpm setting for docking, etc.
Top
Post Reply

Return to “General Repairs & Maintenance”



Who is online

Users browsing this forum: Google [Bot] and 51 guests