Welcome to Carver Yachts Owners Forum
We are a boating forum for owners of Carver Yachts to enthusiastically discuss all aspects of Carver Boat ownership. Whether you are looking for your first Carver or currently own one, you are sure to feel at home on CarverYachtOwners.com
You are currently viewing our board as a guest which gives you limited access to view most discussions, articles and access our other FREE features. By joining our free community you will have access to searching the forum topics, post topics, communicate privately with other members (PM), respond to polls, upload your own photos and access many other special features. Registration is fast, simple and absolutely free so please, join our community today!
Generator
- Thepearl87
- Scurvy Dog
- Posts: 9
- Joined: July 25th, 2021, 1:06 pm
- Vessel Info: 1987,Carver 3607
- Location: Clayton, NY
- Has thanked: 3 times
Generator
Any ideas???
- km1125
- Admiral
- Posts: 3356
- Joined: February 28th, 2017, 6:04 pm
- Has thanked: 60 times
- Been thanked: 976 times
Re: Generator
Don't think the cranking relay fuse would cause the genset to quit running, so I'm wondering what else could be common with that fuse.
- Thepearl87
- Scurvy Dog
- Posts: 9
- Joined: July 25th, 2021, 1:06 pm
- Vessel Info: 1987,Carver 3607
- Location: Clayton, NY
- Has thanked: 3 times
Re: Generator
km1125 wrote:Source of the post Did the fuse actually blow three times and needed to be replaced, or you just replaced it once because it was blown and then a couple times "just in case it was bad"??
Don't think the cranking relay fuse would cause the genset to quit running, so I'm wondering what else could be common with that fuse.
The fuse blew 3 times, then did not blow anymore. I'm going to trace wires from that fuse to be sure there are no voids. If I jump the solenoid contacts, the unit turns over well. But no start. I have jumped the low oil wires, as well as the over heat wires also. Now it's above my feable generator knowledge.
- Thepearl87
- Scurvy Dog
- Posts: 9
- Joined: July 25th, 2021, 1:06 pm
- Vessel Info: 1987,Carver 3607
- Location: Clayton, NY
- Has thanked: 3 times
Re: Generator
- km1125
- Admiral
- Posts: 3356
- Joined: February 28th, 2017, 6:04 pm
- Has thanked: 60 times
- Been thanked: 976 times
Re: Generator
- Thepearl87
- Scurvy Dog
- Posts: 9
- Joined: July 25th, 2021, 1:06 pm
- Vessel Info: 1987,Carver 3607
- Location: Clayton, NY
- Has thanked: 3 times
Re: Generator
- km1125
- Admiral
- Posts: 3356
- Joined: February 28th, 2017, 6:04 pm
- Has thanked: 60 times
- Been thanked: 976 times
Re: Generator
- ColRon
- Admiral
- Posts: 556
- Joined: April 24th, 2017, 6:06 pm
- Vessel Info: 1989 Carver Santego 3867
“Escape Plan” - Location: Murray, KY
- Has thanked: 76 times
- Been thanked: 149 times
Re: Generator
if there’s a way and someone will let me know I can post it on the site here.
1989 Carver Santego 3867
“Escape Plan”
Murray, KY
- Thepearl87
- Scurvy Dog
- Posts: 9
- Joined: July 25th, 2021, 1:06 pm
- Vessel Info: 1987,Carver 3607
- Location: Clayton, NY
- Has thanked: 3 times
Re: Generator
Thanks, I'll print it out when I get it.
I 4hink I have a faulty circuit board. I have it out being tested.
- ColRon
- Admiral
- Posts: 556
- Joined: April 24th, 2017, 6:06 pm
- Vessel Info: 1989 Carver Santego 3867
“Escape Plan” - Location: Murray, KY
- Has thanked: 76 times
- Been thanked: 149 times
Re: Generator
Thepearl87 wrote:Source of the post thepearleightseven@gmail.com
Thanks, I'll print it out when I get it.
I 4hink I have a faulty circuit board. I have it out being tested.
I have sent the service manual in pdf copy to your email.
1989 Carver Santego 3867
“Escape Plan”
Murray, KY
Return to “General Boating Discussion”
Who is online
Users browsing this forum: No registered users and 68 guests