Carver Owners Forum

Was wondering if their is a way to search for previous owners (how many?) and previous registered names of the vessel?

Also is their a way to search the original selling price of a 2002 Carver 346 6.2L mercruiser.

On my 2000 374 voyager the sliding salon entrance door, the frame of the door that opens is corroded badly. I was wondering if anyone know where I might source the side and bottom aluminum pieces in canada. The glass is in excellent shape so if I can replace the aluminum sides and bottom the door would be good as new

Hello, new to forum. not sure if I did it right,
Just purchased a 1984 3607 Aft Cabin and need a harness diagram.
Can you pleas help.
Thanks
BlueDophin
powilson8@juno,com

Hey guys, just picked up my 89 montego 2557 and can’t seem to find the drain plug on the outside of the boat, can anyone tell me where it’s located? Maybe the inside near the transom?

Hi guys,

Apologies, this is my first boat and I’m new to boating…only had her a couple of months and I’m in the process of fixing her up. Had a bad storm roll through in Texas with gust up to 80 mph….I just filed a claim as my swim deck is damaged. Waiting on the estimate but is there a chance the damage goes deeper than just the swim
Deck?

Hi guys,

Hope everyone is well….what do yous guys think?

year 2000 carver 450 voyager pilothouse year 2000 tamd 74P low has boost black smoke starboard side only. port side approx 35psi boost starboard side approx 25psi boost. clean air filters swapped ECMs, no leaks. i think either wastegate or turbo issue. if not the turbo i assume next step is to clean charge air cooler. Is there anything else i should check?

I have a 2006 Carver Voyager 46 with Volvo D9-500's with EVC-B. As of last year I can no longer get the error codes when the warning lights show a code. I follow the correct procedure to hold down the correct EVC button for 5 seconds but it will no longer blink out any codes. It was blinking out codes for the last 4 years but no longer. I even turned off all batteries for 4 days and still not working. Any suggestions ?

Good day everyone.

I am in the process of acquiring the above named Carver, specifically for doing the Loop. My only concern is the bridge clearance for the hardtop version. I do know that electronics will need to be removed but I'm concerned that the hardtop version may still not clear the lowest bridge on the loop.

Is there anyone in this forum with this first hand experience on the Loop with a Carver 450 - Hardtop Version?

I think it will be a challenge to get an actual accurate measurement sitting in the water. I have some ideas on how to do this but would feel more secure if someone actually has first hand experience.

Thanks in advance.

Hey everyone! My name is Israel swartz, I’m from North Carolina, I just picked up a 1989 carver montego 2557, it’s the first cabin cruiser I have owned so this is all new to me, trying to figure it all out as I go, love the boat so far!, after getting the boat and looking at more 2557s up online I noticed that some are a little different then mine like the cabin is set up different and some are the same and also the back of the boat near the swim platform some 2557s go up higher in the back then others, I’m just curious are some just different models or something? Anyway I’m excited to get to know people on here and hope I can learn a lot

Welcome to Carver Yachts Owners Forum

View the latest post Previous owners

View the latest post Aluminium entrance door replacement parts

View the latest post Wiring diagrams for 1984 3607

View the latest post Drain plug

View the latest post Attachment(s) Swim deck damaged from storm.

View the latest post Attachment(s) Wrapped the back of the boat and Carver signs….

View the latest post black smoke exhaust

View the latest post Volvo ECV-B can't read error codes

View the latest post Carver 450 Voyage - Hardtop Version

View the latest post New to the group